Your location is United States. Wrong location or language? Choose a different one below..
Display language is English.
Your currency is USD.
North America
Your location is United States. Wrong location or language? Click here.

Rusan Picatinny rail - Tikka T3 - 20 MOA

Videos
Do you need help with this item?
Our experienced team is here to resolve any issues before, during or after you purchase this item. If you have a question don't hesitate to contact us bellow:
Contact us

Rusan Picatinny rail - Tikka T3 - 20 MOA Details

Introduction

Picatinny rail consists of slots with 5.23 mm spaces between one another, which means that it can be used across its entire length. It is simple to mount and interchangeable – if something is made for a Picatinny rail, it will fit regardless of the manufacturer or manufacturing date. It is affordable, resilient and reliable – this is why it so commonly used by professionals and military. Because of all its great qualities, Picatinny rail has been dominating the rail market in the recent years.

Picatinny is a big step forward from the Weaver standard. Weaver has a few predesignated slots while Picatinny has slots all over its surface, allowing the device to be mounted wherever the user finds it fitting. Weaver's slot is 3.8 mm wide, which is why all mounts made for Picatinny will also fit on a Weaver rail while those made for Weaver will not fit on a Picatinny rail. This is one of the main reasons why Picatinny is a far better mounting solution.

Rusan, a company from Croatia, is one of the manufacturers of Picatinny rails. They make mounts exclusively from steel and provide buyers with a wide selection of Picatinny rails for various rifles. They are made from high quality deep blue finish steel. Picatinny Rails include screws with appropriate thread for the corresponding rifle. Rusan covers 10 years of warranty for all its products.

20 MOA Inclination

20 MOA inclination is only needed when the scope runs out of elevation. For example, when shooting at the range of 100 m, shooter gains 58.2 cm / 100 m of additional elevation range with a 20 MOA mount. This is approximately 5.8 Mrad of elevation. To make things even clearer – if the target was placed at 100 m, the scope with 20 MOA inclined rail would aim to the center of the target while the rifle’s barrel would aim 58 cm higher than the scope. This gives the shooter extra elevation needed for long range shooting. If you plan to shoot on distances longer than 600 meters, use of rail with 20 MOA is greatly recommended. There is no negative effect of the inclined Picatinny rail in the mounting setup if you only shoot on shorter distances. The same goes also the other way around, since if you don’t shoot on extreme distances then Picatinny rail with inclination is not needed.

About the rifle

Tikkakoski factory, the owner of Tikka brand, was established in 1893 in Finland and started manufacturing components for guns in 1918. In 1983, Tikkakoski was merged into Sako. Today, Tikka is a combination of Sako's world famous engineering, values of traditional gunsmith craftsmanship and features of modern-world rifles. Sako became a member of the Beretta group at the turn of the millenium. Since then, it has access to advanced production methods which further enable refining of renowned products.

Tikka T3 is a series of popular bolt-action rifles, available in a wide range of configurations (Hunter, Hunter Stainlesas, Varmint, Varmint Stainless, Forest, Lite, Lite Stainless etc.). Sako chambers Tikka T3 rifles for many calibers: .204 Ruger, .222 Rem., .223 Rem., .22-250 Rem., .243 Win., .25-06 Rem., .260 Rem., 6.5 Creedmoor, 6.5x55, .270 Win., .270 WSM,  7mm-08 Rem., 7mm Rem. Mag., 7x64, .308 Win., .30-06 Sprg., .300 WSM, .300 Win. Mag., 8x57 IS, .338 Federal, .338 Win. Mag. and 9.3x62. There are two locking lugs on the bolt. Barrel length is either 406 mm, 510 mm, 570 mm, 600 mm or 620 mm. In 2016, Tikka series was expanded – T3x was introduced to the public (a series of upgraded T3 models). All improved parts are compatible with the older T3 models. Tikka T3 has a 16.5mm dove-tail on the receiver, along with four mounting holes (two at the front and two at the rear), for mounting purposes. There is a recoil stop on the front mounting surface. The action is push-feed.

Rifles Tikka T3, 55, 65, 558, 590, 690 and Master have similar actions. This is why, for example, two-piece mounts made for Tikka T3 will fit rifles Tikka 55, 65, 558, 590, 690 and Master while one-piece mounts made for Tikka T3 will not fit rifles Tikka 55, 65, 558, 590, 690 and Master. These rifles do not have mounting surfaces with radiuses since they have a dove-tail on the receiver. Tikka rifles have a 16.5 mm dove-tail throughout the entire receiver length.

Mounting details

A: 22 mm
B: 82.2 mm
C: 22 mm
BHU: 1 mm
Fi: M3.5
R1: Prisma 16
R2: Prisma 16

Mounting instructions

Remove all the stains (grease, oil etc.) from the rifle's receiver with a cleaning fluid (acetone). Once the surface is clean and dry, check whether the screws match the rail and the holes on the receiver. Make sure that the Picatinny rail is compatible with the the rifle by inspecting the mounting holes on both. Before mounting the rail permanently, apply a minimal amount of thread-locking fluid 278 or 648 on screws and contact surfaces. Be careful not to get the fluid in or near the mounting holes. Carefully clean the remaining excess fluid around the rail with a cleaning fluid. Using a torque driver, screw the screws appropriately (up to 2.2 Nm) – do not overtighten.

Warranty

The product has a warranty period of 10 years.

Add to Compare Save and send

Rusan Picatinny rail - Tikka T3 - 20 MOA Specifications

ManufacturerRusan
SKU010-12-20MOA
Mount seriesRusan Picatinny Bases
Base typePicatinny
Suitable forTikka T3
A

A, B and C markings refer to the distances between holes on the rail/mount. A is the distance between the front two holes on the rail/mount.

A,B,C distances

22 mm
B

A, B and C markings refer to the distances between holes on the rail/mount. B is the distance between the holes in the middle (usually, that is the distance between the 2nd and 3rd hole on the rail/mount).

A, B, C distances

82.2 mm
C

A, B and C markings refer to the distances between holes on the rail/mount. C is the distance between the rear two holes on the rail/mount.

A, B, C distances

22 mm
BH height

BH stands for Bauhöhe (ger.) which means overall height. It is measured from the mounting surface of the rifle to the lower surface of the riflescope's tube.

BH height

7.5 mm
Inclination

Often, the elevation adjustment that the riflescope offers is not adequate to compensate for the bullet drop when shooting at long range. When the riflescope runs of out of elevation, a mount with an inclination is needed. 20 MOA is the most common inclination. With it, the user gains 58.2 cm / 100 m of additional elevation range when shooting at the range of 100 m. This is approx. 5.8 Mrad of elevation.

20 MOA
MaterialSteel
Length164 mm
Warranty10 years
Made inCroatia
ColorBlack
Why should you trust us? We provide you with:

Reviews for Rusan Picatinny rail - Tikka T3 - 20 MOA

5 By
Quality
Price
Value
5
Fits very well with the low 35mm rings on my Tikka t3.

(Posted on 03/09/2016)

Write Your Own Review

How do you rate this product? *

 1 star2 stars3 stars4 stars5 stars
Quality
Price
Value

Get more info about this product

z Leave a message