Leupold Spotting Scopes Instruction Manual

  • Nina 

Products:

Thank you for choosing a Leupold® spotting scope. We’ve worked tirelessly to make sure it will provide you with a lifetime of performance.

Using Leupold® Spotting Scopes

Leupold spotting scopes are equipped with twist-up eyecups to allow for ease of use by a person with or without eyeglasses. To adjust the eyecup for use while wearing eyeglasses, simply twist the eyecup until it rests in its lowest position.

To extend the eyecup, simply place fingers around the edge of the eyecup and twist it away from the spotting scope.

CHANGING MAGNIFICATION

Magnification levels of Leupold spotting scopes can be changed by rotating the magnification selector located in front of the eyepiece.

While viewing through the scope, turning the magnification selector clockwise increases magnification, while turning it counter-clockwise decreases magnification.

CHANGING THE EYEPIECE (KENAI HD SPOTTING SCOPES ONLY)

TO CHANGE THE EYEPIECE OF THE KENAI HD SPOTTING SCOPE:

1. Firmly grasp the knurled lock ring near the front of the eyepiece and unscrew the entire eyepiece from the body of the spotting scope.
2. Remove the dust cover from the front of the new eyepiece and place it on the eyepiece you just removed.
3. Firmly grasp the knurled lock ring near the front of the new eyepiece and thread the entire eyepiece into the body of the spotting scope.

FOCUSING

TO FOCUS THE IMAGE OF THE LEUPOLD SPOTTING SCOPE:

1. Place the eyecup in the desired position.
2. View the object you desire to observe through the spotting scope.
3. Adjust the magnification level as desired.
4. Turn the focus adjustment dial until the image of the object being viewed is seen as crisp and sharp. For Ventana spotting scopes, the focus dial is located on the upper forward edge of the “shoulder.” For Kenai HD spotting scopes, the focus dial is located around the body of the scope, just in front of the “shoulder.”

USING A TRIPOD

Leupold spotting scopes are equipped with a 1/4-20 thread tripod adapter that will accept the standard 1/4-20 thread mounting screw found on most photographic tripods.

MAINTENANCE

SEALS:
Leupold spotting scopes are sealed from within by several methods, including O-rings and special compounds. All seals are permanent and require no maintenance.

LENSES:
Should the lenses of the scope become dirty, clean them as you would any fine camera lens.

1. Use a lens brush to remove dust.
2. Fingerprints that cannot be removed by brushing can be removed with a good grade of glass cleaner. When wiping the lens, use a soft cloth and wipe from the center of the lens outward.

Warranty Service

Leupold spotting scopes are designed and engineered to standards set and monitored by the design engineers at Leupold’s plant in Oregon. The goal is to provide you with a lifetime of performance.

Should service ever become necessary, your spotting scope is backed by the Leupold Full Lifetime Guarantee. All service work is performed by the Leupold Product Service department in Beaverton, Oregon.

LEUPOLD PRODUCT SERVICE

If your Leupold spotting scope fails to perform in any way, you may return it directly to the factory (or one of our international service centers) for service. We recommend contacting Leupold Technical Service at 1 800-Leupold (538-7653) and following these shipping instructions:

Register your product at: Leupold.com/register
1. Include a note with your name, address, telephone number, e-mail, and a description of the problem.
2. Pack the spotting scope in its original box (if you have it) or another suitably strong shipping box.
3. Wrap the package securely using packing tape on the outside.
4. Ship the spotting scope by parcel or mail service (insured, if possible) to one of the following addresses in the United States:

BY PARCEL SERVICE:
Leupold Product Service
14400 NW Greenbrier Parkway
Beaverton, OR 97006-5791 USA

BY MAIL:
Leupold Product Service
P.O. Box 688
Beaverton, OR 97075-0688 USA

We can also be contacted through our Web site at leupold.com.

FOR SERVICE OUTSIDE THE UNITED STATES:

Canada: Korth Group Ltd., 64186-393 Loop East, Okotoks, AB T1S 0L1, Canada

Australia: Nioa, PO Box 191, Pinkenba, Qld 4008 Australia (for items originating from Australia, New Zealand, New Caledonia and Japan)

South Africa: Formalito, 1019 Pretorius Ave., Lyttelton Manor, 0157, South Africa

THE LEUPOLD LIFETIME GUARANTEE

Anyone can offer you a lifetime warranty, but guaranteeing performance takes serious dedication and craftsmanship. From our Beaverton Oregon factory, to the wilderness, the battlefield, and everywhere in-between, we won’t let you down. If your Leupold scope, sight, binocular or spotting scope doesn’t perform, we will repair or replace it for free, whether you’re the original owner or not – forever.

For complete details visit leupold.com/warranty

 

LEUPOLD, GOLD RING, MARK 4, the Golden Ring design, the circle-L reticle logo design, and various other marks are registered trademarks of Leupold & Stevens, Inc. All marks, including corporate logos and emblems, are subject to Leupold’s rights and may not be used in connection with any product or service that is not Leupold’s, or in any manner that disparages or discredits Leupold, or in a manner likely to cause confusion.

Certain other trademarks used in connection with Leupold products and services are the property of their respective owners, and are used with permission. THE BOONE & CROCKETT CLUB® and BOONE & CROCKETT® are registered trademarks of the Boone & Crockett Club. RMEF® and ROCKY MOUNTAIN ELK FOUNDATION® are registered trademarks of the Rocky Mountain Elk Foundation. Mossy Oak® Break-Up®, Mossy Oak® Break-Up® Country®, Mossy Oak® Break-Up® Infinity™, Mossy Oak® Mountain, Mossy Oak® Obsession®, and Mossy Oak® Treestand®, are trademarks or registered trademarks of HAAS Outdoors, Inc. A.R.M.S. ® is a registered trademark of Atlantic Research Marketing Systems, Inc. The ARD (anti-reflection device) is manufactured by Tenebraex a Division of Armament Technology Incorporated 110 Chain Lake Drive Unit 3E, Halifax NS Canada B3S 1A9 Cordura® is a registered trademark of INvista North America S.A.R.L. Freedom Arms® is a registered trademark of Freedom Arms, Inc. Horus® and Horus Vision® are registered trademarks of Horus Vision, LLC. Kryptek®, Kryptek® Highlander®, and Kryptek® Typhon™ are trademarks or registered trademarks of Kryptek Outdoor Group, LLC. Magnum Research® is a registered trademark of Magnum Research, Inc. Ruger® is a registered trademark of Sturm, Ruger & Company, Inc. Torx® is a registered trademark of Acument Intellectual Properties, LLC. ZEMAX® is a registered trademark of Zemax, LLC. Zygo® is a registered trademark of Zygo Corporation.

For patent information, visit leupold.com/patents

We reserve the right to make design and/or material modifications without prior notice.

Copyright © 2019 Leupold & Stevens, Inc. All rights reserved.

Leave a Reply

Your email address will not be published. Required fields are marked *