Product: https://www.optics-trade.eu/en/holosun-tube-hs406c.html
This text is a transcription of the file in PDF format.
Thank you for purchasing the product from HOLOSUN , the
TUBE HS406C1 is a monocular red dot sight , before operation,
please read the User’s Manual carefully.
Features
1. Aiming secretively : aiming with the red dot in sight , no light
can be detected by sighted object.
2. Full field of view for target aiming : Aiming with two eyes open,
rapid target acquisition and environment control.
3. Solar power supply: The device is driven by solar power(silicon
solar cell) , power is ready for use all the time.
4. Two-path-power supply design : it can be shift to normal
battery supply under dark surrounding.
5. Low power consumption : Only several microamperes current
for sight operation . Working life with one battery can be
30000 hours , No need for caring the battery replacement.
6. Parallax free of optical system . Target mark (dot) parallax
≤±1MOA.
7. Auto power turn-off : The power of device will be
automatically turned off after 8 hours’ non-operation
(operation stagnation).
8. Brightness adjustment:12 settings for brightness of target
mark with different ambient light conditions.
9. One Button switch : Easy operation , reduce obstruction
to vision.
10. The Mount bracket is compatible with sniper rifle.
11. Waterproof : Ip67
Important notices
1.You Must check carefully and make sure for 100% to unload
the bullet from your firearms before any actions taken such
as device installation , beam adjusting or changing new
battery . Ensure all the operation is under safe condition.
2. Always make sure to point the weapon muzzle to ground
direction when you replace the battery.
3. Please keep the inner package for future maintenance
mailing purpose. Other packaging material may be
disposed properly.
Battery
1. The operating voltage for this device is DC3V using one
high quality CR2032 Lithium battery included with
purchase.
2. The high quality battery can power the device for up to
30,000 hours. Caution: The battery is not rechargeable.
3. Battery replacement:
1) Removing the battery (Fig 2-1):
a) Loosen screws 1, 2.
b) Insert coin or similar
object in the battery
tray slot, pry out the
battery tray, and
remove the discharged
battery by lifting it up.
A tool is provided.
2) Battery installation (Fig2-2):
a) Insert the battery into
the battery tray by
pushing it down with
the correctly marked
polarities, “+” and “-“.
b) Insert and press the
tray into the battery
compartment.
c) Tighten screws 1, 2.
Installation
1. The Mount bracket(Fig 3) is for
connecting weapon with the sight.
2. Connection bracket with the sight:
1) Screw off the 6 screws with the
hex wrench, take off the upper cover.
2) Mount the sight on the bracket
follow the direction and position which are shown in Fig4.
3) Close the upper cover , and fit and fasten the 6 screws on.
3. Connection the bracket with weapon:
1)The mount bracket is adaptable to the arms with Picatinny
rail,If the arms have no Picatinny
rail,or with other types of rail,
Please make extra remarks in your
purchase order.
2) Firstly insert the allen wrench
into the clamp screw hole, then
rotate to loosen the convex set
(as shown in Fig3), slid the sight into the weapon rail to a right
position, and finally fasten the clamp screw.
Sight operation
Two operation modes are available:
Auto mode and manual mode.
1. Auto mode (default) – with solar
cell and internal battery two-way
power supply:
Based upon the ambient lighting
level, the sight will switch
between battery and solar cell power automatically for
operation in all lighting conditions.
Auto mode operation:
a) Sight is always in auto mode unless specifically switched
to manual mode.
b) While in auto mode, the brightness of the reticle is
automatically adjusted to match ambient lighting. The
brighter it is, the higher the dot intensity.
c) If lighting is low enough, the sight will automatically
switch to the battery. While running on battery, you can
adjust the reticle brightness using the “+”and “-” buttons
to switch between levels 3, 4, or 5.
2. Manual Mode (Internal battery power only mode):
a) Press down the “+”button for 3 seconds to enter into
the Manual Mode.
b) Brightness adjustment: There are 12 settings for reticle
brightness level under manual mode. The default
brightness is at 7 when the device is switched to this
mode. The brightness can be adjusted as required by
pressing the “+”or “-” to increase or decrease the
brightness level , one press for one change in brightness
level.
c) Switching back to auto mode:
Simultaneously press the “+”and “-“buttons to switch to
auto mode. The device will also switch automatically
from manual mode to auto mode if there has been no
other button operation in 12 hours.
Note: In summary, the sight is always ready for use, no matter
what the lighting conditions are.
Zero setting
1. On top of sight is the elevation adjusting knob, windage
adjusting knob is on the right side (see Fig6), The sight has
been primarily adjusted in factory.
2. First open the protective lid(see Fig6), position slot type
screwdriver on the slotted screw, then rotate the screw to
right or left for adjustment. Each left or right click is for
one shift moving equivalent to 0.5 MOA value.
3. Right turning the elevation knob will moving the red dot
up, left turning will lower the red dot, similar to the
windage adjusting, right turning will move the red dot to
right, left turning will move it to left.
4. Caution: Don’t try to rotate the knobs, if you feel the knobs
cannot be rotated which proves the adjustment limits.
Otherwise the device may be damaged. If the adjusting
range is beyond the limits, consider to add extra spacer
between the device and mount rail to expand the adjusting
range limits.
Maintenance and care
This device is a precision instrument that deserves reasonably
cautious care. The following tips are provided to ensure long
lasting use of the sight.
The optical system including the objective window and
eyepiece lens which are multi-coated optical glass. When
cleaning the lenses, blow away the dust on surface, wet the lens
with lens cleaner or clean water, wiping the fingerprint and oil
stain with lens tissue, soft cotton or microfiber cloth. No special
maintenance needed for housing surface. Avoid touching the
glass surface with dry cloth or tissue paper. No organic solvents
such as alcohol, acetone are allowed. Don’t try to dismantle the
device as the internal parts are specially cleaned and sealed and
with anti-fog treatment,Any such attempt will void the warranty.
If repair needed, you can call our customer service center, or
login in our website ,or send email to us.
Limited Warranty
SUMMARY
We provide limited lifetime warranty from the date of
purchase on parts and workmanship to the original purchaser.
At our sole discretion, we will repair or replace product found
to be defective under normal use and service without charge
excluding any delivery costs, which will be born by purchaser.
We will not be liable for incidental,consequential,or special
damages arising out of or in any connection with the use or
performance of this product. This warranty is void if the
product has been misused, modified, neglected, or
disassembled prior to its return.
Please refer to http://www.holosun.com for current and
complete warranty information.
TUBE HS406C1
Red Dot sight
