RCBS Collet 8mm/323 for Bullet Puller

• Caliber-Specific Grip: Sized for 8mm/.323 bullets, this collet gives the bullet puller a secure hold on the projectile so loaded rounds can be broken down with less risk of slipping or marking the bullet.
• For Jacketed and Monolithic Bullets: The design is intended for FMJ, JHP, HP and all-copper or copper-clad bullets, making it a practical choice for reloaders working across common hunting and target bullet types.
• Hardened Steel Construction: The steel build resists wear from repeated clamping and release cycles, helping the collet maintain consistent grip and service life on the loading bench.
• Works with the RCBS Standard Bullet Puller: Made for the RCBS Standard Bullet Puller body, it turns the puller into a caliber-matched tool for safe component recovery when correcting loads or salvaging brass and bullets.
• Made in USA: Domestic manufacture aligns with RCBS’s long-established reloading-tool production and gives experienced handloaders a part built to the same standard as the rest of the system.

About the RCBS Bullet Puller Collet Series

RCBS Bullet Puller Collets are caliber-specific accessories made for the company’s Standard Bullet Puller. Within the RCBS reloading lineup, they serve a focused but important role: allowing handloaders to match the puller body to the bullet diameter they need to remove. This modular approach makes more sense than a one-size-fits-all design, because the collet can grip the bullet correctly while helping preserve the components for reuse.

The series is intended for reloaders who need to correct powder charges, change bullet selections, or disassemble loaded ammunition without unnecessary damage. RCBS builds these collets from hardened steel and machines them to precise tolerances, which is essential for repeatable clamping pressure and clean bullet removal. In practical use, the series is aimed at bench reloaders who value component recovery and controlled operation over impact-style pulling methods. As part of the broader RCBS ecosystem of presses, dies and case-preparation tools, these collets fit naturally into a methodical reloading workflow where consistency and reduced component loss matter.

About the RCBS Collet 8mm/323 for Bullet Puller

The RCBS Collet 8mm/323 for Bullet Puller is the caliber-matched insert for reloaders working with .323-inch / 8mm bullets. Its job is simple but important: it gives the RCBS Standard Bullet Puller the correct gripping surface for this bullet diameter, so loaded cartridges can be taken apart in a controlled way. That matters when a handloader needs to correct a load, recover an expensive projectile, or salvage primed brass and powder components with less waste.

This model is intended for use with jacketed and monolithic bullets, including common FMJ, hollow-point and copper bullet designs. In practice, that makes it useful for both range ammunition and hunting loads built around 8mm projectiles. Because the collet is made from steel, it stands up well to repeated use and maintains the firm, even grip needed for reliable bullet extraction. Its compact format also keeps setup straightforward: once paired with the Standard Bullet Puller body in a compatible press, it becomes a dedicated solution for this specific caliber rather than a compromise tool.

For reloaders who prefer a bench-mounted pulling method, this collet offers a cleaner and more controlled alternative to impact pulling. The result is better component preservation, less bench mess, and more confidence when disassembling ammunition that needs to be corrected or repurposed.

About RCBS

RCBS was founded in 1943 by Fred T. Huntington in Oroville, California. The company name came from Rock Chuck Bullet Swage, Huntington’s original bullet-swaging die, and that origin still reflects RCBS’s close connection to practical handloading tools. Today, RCBS is based in Oroville, California, United States, and is known for equipment built around rifle and pistol cartridge reloading.

The brand focuses on ammunition handloading and reloading equipment, with product lines that include presses, dies, shell holders, powder measures and priming tools. RCBS also manufactures reloading tools in Oroville, California, which keeps the brand closely tied to its long-running production base. In 2024, RCBS became a brand of Hodgdon Powder Company after its sale by Revelyst, but it remains one of the established names in metallic cartridge reloading equipment.

Main Features

• Manufacturer: RCBS
• Product Type: Bullet Puller Collet
• Caliber Compatibility: 8mm/.323
• Made in: USA
• Material: Steel
• Color: Silver
• Weight: 50.00 g
• Length: 76.00 mm

Warranty

RCBS covers this product for 2 years. That period suits a simple steel reloading accessory intended for repeated bench use with the matching bullet puller system.