RCBS Collet 6mm/243 for Bullet Puller

• Caliber-specific 6mm/.243 fit: Sized for 6mm and .243 bullets, this collet gives the RCBS bullet puller a secure grip on the projectile so bullets can be removed cleanly during load correction or component recovery.
• Works with the RCBS Standard Bullet Puller: Built to pair with the standard puller body, it turns the tool into a caliber-matched setup that is easier to use consistently when breaking down loaded cartridges.
• Hardened steel construction: The steel body resists wear from repeated clamping and pulling, helping the collet maintain reliable holding force over time in regular reloading use.
• Protects reusable components: By gripping jacketed bullets correctly, the collet helps pull bullets without unnecessary damage, which is useful when salvaging bullets and preserving brass, powder, and primers where appropriate.
• Compact reloading accessory: Its small size and simple format make it easy to keep alongside bullet pulling and case-preparation tools without adding bulk to the bench.

About the RCBS Bullet Puller Collet Series

RCBS Bullet Puller Collets are caliber-specific accessories made for the company’s Standard Bullet Puller. In the RCBS reloading lineup, they serve a practical bench role: turning a general puller body into a cartridge-appropriate tool for safely disassembling loaded ammunition. Rather than relying on a one-size-fits-all grip, each collet is matched to a bullet diameter range, which improves purchase on the projectile and makes the pulling process more controlled.

The series is intended for reloaders who need to correct seating depth mistakes, recover components from test loads, or break down ammunition for inspection. RCBS builds these collets from hardened steel and machines them to precise tolerances so they can repeatedly clamp jacketed and monolithic bullets with dependable consistency. That approach suits both occasional bench use and more frequent reloading work. Across the series, the main advantage is straightforward: a caliber-matched collet helps remove bullets with less risk of slipping, distortion, or unnecessary damage to components that may still be reused.

About the RCBS Collet 6mm/243 for Bullet Puller

The RCBS Collet 6mm/243 for Bullet Puller is the caliber-specific insert for reloaders working with 6mm and .243 bullets. Its job is simple but important: it gives the RCBS Standard Bullet Puller the correct gripping surface for this bullet diameter, so loaded rounds can be taken apart in a controlled way. That matters when a handload needs to be corrected, when components must be recovered from experimental loads, or when ammunition is being inspected after assembly.

Because the collet is matched to the bullet size, it offers a more secure hold than a generic solution. In practice, that means steadier clamping on jacketed bullets and a better chance of removing the projectile without excessive marking or deformation. For reloaders, the benefit is not just convenience; it is the ability to preserve valuable components and keep the disassembly process predictable at the bench.

RCBS makes this collet from steel, which suits the repeated compression and pulling forces involved in bullet removal. Its 76.00 mm length and 50.00 g weight keep it compact and easy to handle, while the simple silver-finished form fits naturally into a reloading setup focused on function rather than complexity. As an accessory for bullet pulling and case-preparation work, this model is a practical match for reloaders who regularly handle .243-caliber ammunition.

About RCBS

RCBS was founded in 1943 by Fred T. Huntington in Oroville, California. The company name came from Rock Chuck Bullet Swage, Huntington’s original bullet-swaging die, and that origin still reflects the brand’s close connection to practical handloading tools. RCBS specializes in ammunition handloading and reloading equipment for rifle and pistol cartridges, with product lines that include presses, dies, shell holders, powder measures, and priming tools.

RCBS manufactures reloading tools in Oroville, California, and the brand remains closely associated with bench equipment built for repeatable loading work. Its range covers single-stage, turret, and progressive presses, showing a focus on both entry-level and more advanced reloading setups. Since 2024, RCBS has been a brand of Hodgdon Powder Company, linking one of the best-known names in reloading tools with a long-established powder and components business.

Main Features

• Manufacturer: RCBS
• Product type: Bullet puller collet
• Caliber compatibility: 6mm / .243
• Made in: USA
• Material: Steel
• Weight: 50.00 g
• Length: 76.00 mm
• Color: Silver
• Application: Case preparation

Warranty

RCBS provides a 2-year warranty for this product. That period suits a bench accessory intended for repeated reloading and bullet-pulling use.