Picatinny rail consists of slots with 5.23 mm spaces between one another, which means that it can be used across its entire length. It is simple to mount and interchangeable – if something is made for a Picatinny rail, it will fit regardless of the manufacturer or manufacturing date. It is affordable, resilient and reliable – this is why it so commonly used by professionals and military. Because of all its great qualities, Picatinny rail has been dominating the rail market in the recent years.
Picatinny is a big step forward from the Weaver standard. Weaver has a few predesignated slots while Picatinny has slots all over its surface, allowing the device to be mounted wherever the user finds it fitting. Weaver's slot is 3.8 mm wide, which is why ring mounts made for a Weaver rail will also fit on a Picatinny rail while ring mounts made specifically for a Picatinny rail will not fit on a Weaver rail. This is one of the main reasons why Picatinny is a far better mounting solution.
MAK is one of the biggest mount manufacturers in Germany. All of their Picatinny rails are manufactured from high-quality steel and are known for their mat finish that does not reflect light. The edges of the rails are wavy, adding to the high-quality appearance. MAK Picatinny rails lack a slot that would allow the user to use the Picatinny rail with sights.
Sauer & Sohn is a firearms manufacturing company with a long tradition – it was founded in 1751 and is thus the second oldest gun manufacturer in the world. One of their most known firearms is Sauer 38H, an advanced semiautomatic pistol that was produced in great numbers – it featured a cocking/decocking lever. They partnered with Swiss company SIG in 1976 – a new line of semi-automatic pistols was launched, branded SIG Sauer.
Sauer 202 Magnum is made in a wide selection of calibers: .270 Wby. Mag., 7 mm Rem. Mag., .300 Win. Mag., .300 Wby. Mag., 8x68S, .375 H&H Mag., .416 Rem. Mag., .458 Lott. The rifle operates on modular barrel change system which allows the user to switch barrels and thus use different calibers. There are two holes on each of the mounting surfaces. Unlike Sauer 202 Standard, Magnum version is only available with a steel receiver.
Sauer 202 Magnum has a similar action as Sauer 202 Medium (Standard). The radiuses of the mounting surfaces are the same but there is a difference in B distance (see the picture below). This is why two-piece mounts made for Sauer 202 Magnum will fit Sauer 202 Medium (Standard) while one-piece mounts made for Sauer 202 Magnum will not fit Sauer 202 Medium (Standard).
A: 21.84 mm
B: 100.2 mm
C: 21.84 mm
BHU: 1.5 mm
Remove all the stains (grease, oil etc.) from the rifle's receiver with a cleaning fluid (acetone). Once the surface is clean and dry, check whether the screws match the rail and the holes on the receiver. Make sure that the Picatinny rail is compatible with the rifle by inspecting the mounting holes on both. Before mounting the rail permanently, apply a minimal amount of thread-locking fluid 278 or 648 on screws and contact surfaces. Be careful not to get the fluid in or near the mounting holes. Carefully clean the remaining excess fluid around the rail with a cleaning fluid. Using a torque driver, screw the screws appropriately (up to 2.2 Nm) – do not overtighten.
The product has a warranty period of 10 years.
|Mount series||MAK Picatinny rails|
|Suitable for||Sauer 202 Magnum|
A, B and C markings refer to the distances between holes on the rail/mount. A is the distance between the front two holes on the rail/mount.
A, B and C markings refer to the distances between holes on the rail/mount. B is the distance between the holes in the middle (usually, that is the distance between the 2nd and 3rd hole on the rail/mount).
A, B and C markings refer to the distances between holes on the rail/mount. C is the distance between the rear two holes on the rail/mount.
BH stands for Bauhöhe (ger.) which means overall height. It is measured from the mounting surface of the rifle to the lower surface of the riflescope's tube.
Often, the elevation adjustment that the riflescope offers is not adequate to compensate for the bullet drop when shooting at long range. When the riflescope runs of out of elevation, a mount with an inclination is needed. 20 MOA is the most common inclination. With it, the user gains 58.2 cm / 100 m of additional elevation range when shooting at the range of 100 m. This is approx. 5.8 Mrad of elevation.
(Posted on 09/03/2016)