Picatinny rail consists of slots with 5.23 mm spaces between one another, which means that it can be used across its entire length. It is simple to mount and interchangeable – if something is made for a Picatinny rail, it will fit regardless of the manufacturer or manufacturing date. It is affordable, resilient and reliable – this is why it so commonly used by professionals and military. Because of all its great qualities, Picatinny rail has been dominating the rail market in the recent years.
Picatinny is a big step forward from the Weaver standard. Weaver has a few predesignated slots while Picatinny has slots all over its surface, allowing the device to be mounted wherever the user finds it fitting. Weaver's slot is 3.8 mm wide, which is why ring mounts made for a Weaver rail will also fit on a Picatinny rail while ring mounts made specifically for a Picatinny rail will not fit on a Weaver rail. This is one of the main reasons why Picatinny is a far better mounting solution.
EAW is a German company, known for producing top-quality mounts. Their Picatinny rails, which are all made from steel, have a nice finish and come with a unique channel in the middle, allowing the user to clearly see the rifle's sights. Screws are included. EAW chooses only the best materials for their products. All of these great features; however, come at quite a steep price.
Fabarm was established around 1900 by the Galesi family in Brescia, Italy. In the beginning, they produced mostly pistols and side-by-side shotguns. During the 1950s, Fabarm started producing compressed air rifles and Flaubert carbines followed by its first semi-auto shotgun, the Fabarm Goldenmatic.
Fabarm Iris is a bolt-action rifle with a 60 degree bolt lift that can be chambered for the following calibers: .223 Rem., .243 Win., .270 Win., .308 Win., 7x64, .30-06 Spr., 9,3x62, .270 WSM and .300 WM. It has a manual cocking system with a 60° bolt lift and features a free-floating barrel made in Germany. The user can choose from DTG (Direct trigger system) or STG (Set trigger system). There are two mounting holes on each side of the mounting surface. The ejection port is located on the right side.
Rifles Benelli Argo, Browning BAR, Browning Acera, Browning Maral, Winchester SXR Vulcan and Fabarm Iris have actions of the same dimensions, which is why they share the same mounts.
A: 12.7 mm
B: 81 mm
C: 12-7 mm
BHU: 0 mm
Remove all the stains (grease, oil etc.) from the rifle's receiver with a cleaning fluid (acetone). Once the surface is clean and dry, check whether the screws match the rail and the holes on the receiver. Make sure that the Picatinny rail is compatible with the rifle by inspecting the mounting holes on both. Before mounting the rail permanently, apply a minimal amount of thread-locking fluid 278 or 648 on screws and contact surfaces. Be careful not to get the fluid in or near the mounting holes. Carefully clean the remaining excess fluid around the rail with a cleaning fluid. Using a torque driver, screw the screws appropriately (up to 2.2 Nm) – do not overtighten.
The product has a warranty period of 30 years.
|Mount series||EAW Picatinny Rails|
|Suitable for||Benelli ARGO / Spec., Browning Acera, Browning BAR I / BAR II, Browning Maral, Fabarm Iris, Winchester SXR Vulcan|
A, B and C markings refer to the distances between holes on the rail/mount. A is the distance between the front two holes on the rail/mount.
A, B and C markings refer to the distances between holes on the rail/mount. B is the distance between the holes in the middle (usually, that is the distance between the 2nd and 3rd hole on the rail/mount).
A, B and C markings refer to the distances between holes on the rail/mount. C is the distance between the rear two holes on the rail/mount.
BH stands for Bauhöhe (ger.) which means overall height. It is measured from the mounting surface of the rifle to the lower surface of the riflescope's tube.
Often, the elevation adjustment that the riflescope offers is not adequate to compensate for the bullet drop when shooting at long range. When the riflescope runs of out of elevation, a mount with an inclination is needed. 20 MOA is the most common inclination. With it, the user gains 58.2 cm / 100 m of additional elevation range when shooting at the range of 100 m. This is approx. 5.8 Mrad of elevation.